Account Navigation

Account Navigation

Currency - All prices are in AUD

Currency - All prices are in AUD
 Loading... Please wait...
Kink Engineering

How to build a Vac Cube

HOW TO ASSEMBLE YOUR VAC CUBE

 

You will need:

7 x 3 way corners (Included)

 

1 x 4 way corner (Included)

 

1 x 1 way valve (Included)

 

12 x 33” long 1.5” ABS Pipe

 

Medium grit sandpaper

 

Drill with a 5cm (3/16”) drill bit

 

 

Prepare frame parts

Cut the 1.5” ABS pipe into 12, 33” tubes. You will need to drill small (5mm or 3/16”) holes through the pipe to allow air to be drawn out of the bed by the vacuum. Drill one hole every 15cm (6”) or so. Drill in one side of the pipe and out the other. Turn the pipe 90 degrees and do this again.

drillinfographic.png

Now you will need to sand all the holes you just drilled so that there are no rough edges. Latex will pop like a balloon if punctured so this is an important step.

 

Now you can assemble your frame!

 

Building Your Frame

 

This is where a friend comes in handy.....

 

 

Lay your your cube bag on the floor with the neck gasket at the top of the cube and climb inside. Have someone hand you 3 of the 3 way corners and the 4 way corner along with 4 lengths of 33” pipe. While in the cube locate the hole for the 4 way corner and start there. Assemble the bottom of the cube then build up from there. PLEASE BE CAREFUL to not pinch the latex in between the pipe and the corner fittings.

 

At this point you can chose to tape the corners of the cube together for more stability. This is a good idea if you aren't planning on taking it down and storing it away but is not a necessary step.

 

To seal your vacbed for use you will want to add a bit of tape (hockey tape the best choice we have found as this will not leave a residue) to the outside of the reinforced hole by the 4 way corner. This will stop any small leakage of air back into your bed from that area.

 

Its time to get into your vacbed and try it out! Get your friend to help you turn on/off the vacuum and close up the bed after you get inside. They are also there to make sure you are safe, happy and well played with. 

 

NEVER USE YOUR VACBED ALONE! NEVER!

 

 

USING YOUR VAC BED!!!

 

Climb inside the cube by stretching the opening downward and crawling in. Position yourself below the neck gasket and reach up with both hands in a prayer position and stretch the neck gasket down over your head to your neck making sure it lays flat against your skin like a turtleneck sweater. If the gasket is too lose you can use a bit of hockey tape to seal it around the neck but BE CAREFUL and always have an easy way out.

 

Your partner can now smooth out the open end of the cube and sandwich the top and bottom pieces of latex between the closure bar and the cord. This will prevent air leakage from the entrance of the vacbed.

  • Make sure that the closure bar is fully closed. Sometimes when pushing the tube into the closure bar it will make a crunching sound. This is OK.

  • If you are still having trouble adding some lube to the latex at the closure bar should make it easier to close.

 

Slide the one way valve into the 4 way corner that is now sticking out of the cube and secure it with a little tape. Attach your vacuum cleaner to the one way valve (again tape is the easiest way to do this) and your ready to go!

 

Turn the vacuum on for about 30 seconds. The cube will seal around you if all is assembled correctly and stay sealed when you turn the vacuum off.

  • If the bed is re-inflating quickly check to see where the air is getting back in. Usually it is from the neck gasket not sitting flush or the closure bar not being sealed all the way.

  • Another common issue is leaking around the reinforced hole for the one way valve. A bit of tape should correct this.

     

YOUR DONE! Go have fun kids. PLAY SAFE!

 

 

 

 

 

 

QUESTIONS? CONSERNS? COMMENTS? SUGGESTIONS?

We would be more than happy to hear from you and help you out!

  1. Check out our FAQ section at: http://elasticaengineering.com/faq/

     

  2. Check out our “How To” videos : https://www.youtube.com/channel/UCXnO51gmvuF_XxetjvLMGDQ

     

  3. E-mail us at: info@kinkengineering.com

 

 

 

 

Care instructions:

Wash bed with soap and water. Antibacterial dish soap is great for this.

Hang to dry, then flip inside out and hang to dry again.

When storing your bed always lube or powder it with talc.

Placing in an air tight bag is recommended.

Keep out of direct sunlight.

Keep away from metal. May stain or degrade the latex.

Have fun!